Looking for:
Intex saltwater system manual |
INTEX Krystal Clear™ Saltwater Pool Chlorine System - 7, Gal.Intex ECO 20110 Owner's Manual
Actual product may vary. Not to scale. Operation is subject to the following two conditions: 1 this device may not cause interference, and 2 this device must accept any interference, including interference that may cause undesired operation of the device. It will destroy the bacteria, oxidize bather organics and control algae, which provide a safe, clean and comfortable swimming pool. This location extends the life of the titanium plates.
Go directly to step 2 if your pool is empty. If your above-ground-pool is filled with water, unscrew the strainer grids from the strainer connectors and insert the black hat-like plugs into the connectors, before installing the saltwater pool system.
This is depicted in Drawings 1 and 2. It is also acceptable to use water conditioning salt pellets the compressed forms of evaporated salt. However, it will take a longer time for them to dissolve. Do not use iodized or yellow yellow prussiate of soda colored salt. Salt is added to the pool water and the electrolytic cell uses the salt to create chlorine. Turn on the filter pump. Switch on the unit. Page 18 Once the boost is operating, check whether the filter pump operating hours have been set properly.
For example, the boost operating time is 16 hours, the filter pump should be set to run for 17 hours at least. Increase the filter pump operating time if necessary. Also close the plunger valves on your pool or insert the black hat-like plugs in the strainer opening to prevent water spillage. After completing all maintenance tasks, you must plug the power cord back in and open the plunger valves or remove the plugs.
The 6-way valve has three hose connection ports. Page 13 Remove the drain valve 3 from the 6-way valve outlet and connect the hose to the outlet. In a counter-clockwise motion unscrew plunger valve union from the threaded strainer connector Grasp the plunger valve assembly. Make sure the step washer 30 is in place. Connect adaptor B 35 to plunger valve union. Connect this product only to a grounding type receptacle protected by a ground-fault circuit interrupter GFCI or residual current device RCD.
The pump should never be on when the valve is in the closed position. Vacuuming device i. Intex auto pool cleaner attached to the system may also cause the flow to diminish and the pressure to rise.
Remove any vacuuming device from the system and check if the pressure gauge reading has dropped from the yellow zone to the green zone. Switch on the unit. This indicates that the saltwater system has started E. It is also acceptable to use water conditioning salt pellets the compressed forms of evaporated salt. However, it will take a longer time for them to dissolve. Do not use iodized or yellow yellow prussiate of soda colored salt. To maintain the pool water clear and clean, and to maximize the performance of the device, add cyanuric acid to the pool.
Make sure the filter pump is switched off, then disconnect the power cord from the electrical outlet. In most cases this self cleaning action will keep the electrodes working at optimum efficiency. We recommend that you test the water chemistry weekly, and maintain the chlorine concentration at 0. If anti-freeze solution is needed, use only propylene glycol. While all accidents cannot be prevented, practicing good safety habits, setting and following rules, carefully reading instruction manuals, and vigilant supervision can greatly reduce the likelihood of injury as well as reduce injury severity.
Please take the time to review the following information, and make use of the link provided, to assist in keeping you and your family safe from injury. You save. Decrease Quantity: Increase Quantity:. Shop Replacement Parts. Keeps Water Sparkling Clear!
Shop at a Retail Partner. Write Review. Rating Required Select Rating 1 star worst 2 stars 3 stars average 4 stars 5 stars best.
Email Required. Review Subject Required. Comments Required.
Intex saltwater system manual.Krystal Clear™ Saltwater Pool Chlorine System - 7,000 Gal
Monday through Friday, am to pm Pacific Time. Previous Page. Next Page. Due to a policy of continuous product improvement, Intex Always supervise children and those with disabilities. NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale. Operation is subject to the following two conditions: 1 this device may not cause interference, and 2 this device must accept any interference, including interference that may cause undesired operation of the device.
It will destroy the bacteria, oxidize bather organics and control algae, which provide a safe, clean and comfortable swimming pool. This location extends the life of the titanium plates. Go directly to step 2 if your pool is empty. If your above-ground-pool is filled with water, unscrew the strainer grids from the strainer connectors and insert the black hat-like plugs into the connectors, before installing the saltwater pool system. This is depicted in Drawings 1 and 2. It is also acceptable to use water conditioning salt pellets the compressed forms of evaporated salt.
However, it will take a longer time for them to dissolve. Do not use iodized or yellow yellow prussiate of soda colored salt. Salt is added to the pool water and the electrolytic cell uses the salt to create chlorine.
Turn on the filter pump. Switch on the unit. Page 18 Once the boost is operating, check whether the filter pump operating hours have been set properly. For example, the boost operating time is 16 hours, the filter pump should be set to run for 17 hours at least. Increase the filter pump operating time if necessary. Also close the plunger valves on your pool or insert the black hat-like plugs in the strainer opening to prevent water spillage.
After completing all maintenance tasks, you must plug the power cord back in and open the plunger valves or remove the plugs. Flow Sensor Cleaning 1.
In a counter-clockwise motion unscrew the collar of the flow sensor 7 and remove it from the electrolytic cell conduit. Disconnect the 2 hoses from the Saltwater System, and assemble the cell cover 10 at each side of the cell. In a counter-clockwise motion, unscrew the collar of the copper electrode 5 and remove it from the electrolytic cell 4.
Grasp the plunger valve assembly. Make sure the step washer 30 is in place. Connect adaptor B 35 to plunger valve union. Connect this product only to a grounding type receptacle protected by a ground-fault circuit interrupter GFCI or residual current device RCD. The pump should never be on when the valve is in the closed position. Vacuuming device i. Intex auto pool cleaner attached to the system may also cause the flow to diminish and the pressure to rise.
Remove any vacuuming device from the system and check if the pressure gauge reading has dropped from the yellow zone to the green zone. Switch on the unit. This indicates that the saltwater system has started E.
It is also acceptable to use water conditioning salt pellets the compressed forms of evaporated salt. However, it will take a longer time for them to dissolve. Do not use iodized or yellow yellow prussiate of soda colored salt. To maintain the pool water clear and clean, and to maximize the performance of the device, add cyanuric acid to the pool. Make sure the filter pump is switched off, then disconnect the power cord from the electrical outlet.
In most cases this self cleaning action will keep the electrodes working at optimum efficiency. We recommend that you test the water chemistry weekly, and maintain the chlorine concentration at 0. If anti-freeze solution is needed, use only propylene glycol. Propylene glycol is non-toxic and will not damage plastic system components; Electrolytic cell cord is loose. Replace 4. Possible electrolytic cell failure. High salt level. However, it involves inherent risks of injury and death. To reduce your risk of injury, read and follow all product, package and package insert warnings and instructions.
All Intex products have been inspected and found free of defects prior to leaving the factory. The provisions of this Limited Warranty apply only to the original purchaser and is not transferable. This manual is also suitable for: Eco Cs Print page 1 Print document 35 pages. Rename the bookmark. Delete bookmark?
INTEX CS OWNER'S MANUAL Pdf Download | ManualsLib.Order & Delivery Updates
Table Of Contents. Quick Links. Table of Contents. Don't forget to try these other fine Intex products: Pools, Pool. Boats available at fine retailers or visit our intex saltwater system manual listed below.
Due to a policy of continuous product improvement, Intex. To purchase parts and accessories or to obtain non-technical assistance, Visit. For technical assistance and missing parts call us toll-free for U.
Monday through Friday, am to pm Pacific Time. Previous Page. Next Page. Due to a policy of continuous product improvement, Intex Always supervise children and those with disabilities. NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale. Operation intex saltwater system manual subject to the following two conditions: 1 this device may not cause interference, and 2 this device must accept any interference, including interference that may cause undesired operation of the device.
It will destroy the bacteria, oxidize bather organics and control algae, which provide a safe, clean and comfortable swimming pool. This location extends the life of the titanium plates. Go directly to step 2 if your pool is empty. If your above-ground-pool is filled with water, unscrew the strainer grids from the strainer connectors and insert the black hat-like plugs into the connectors, before installing the saltwater pool system.
This is depicted in Drawings 1 and 2. It is also acceptable to use water conditioning salt pellets the compressed forms of evaporated salt. However, it will take a longer time intex saltwater system manual them to dissolve.
Do not use iodized or yellow yellow prussiate of soda colored salt. Salt is added to the pool water and the electrolytic cell uses the salt to create chlorine.
Turn on the filter pump. Switch on the unit. Intex saltwater system manual 18 Once the boost is operating, check whether the filter pump operating hours have been set properly. For example, the boost operating time is 16 hours, the filter pump should be set to run for 17 hours at least. Increase the filter pump operating time if necessary. Also close the plunger valves on your pool or insert the black hat-like plugs in the strainer opening to prevent water intex saltwater system manual.
After completing all maintenance tasks, you must plug the power cord back in and open the plunger valves or remove the plugs.
Flow Sensor Cleaning 1. In a counter-clockwise motion unscrew the collar of the flow sensor 7 and remove it from the electrolytic cell conduit. Disconnect the 2 hoses from the Saltwater System, and assemble the cell cover 10 at each side of the cell. In a counter-clockwise motion, unscrew the collar of the copper electrode 5 and remove it from the electrolytic cell 4. Possible electrolytic cell failure. Replace the cell if needed. High salt level.
However, it involves inherent risks of injury and death. Gin rummy windows 10 reduce your risk of injury, read and follow all product, package and package insert warnings and instructions.
Remember, intex saltwater system manual, that product warnings, instructions and safety вот ссылка cover some common risks of water recreation, but do not cover all risks and dangers. A competent adult should be appointed as /22900.txt Page Limited Warranty Intex saltwater system manual Center. Upon receipt of the returned product, the Intex Service Center will inspect the item and determine the validity of the claim.
If the provisions of intex saltwater system manual warranty cover the item, the item will be repaired or replaced at no charge. Print page 1 Print document 27 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Restore password. Upload manual. Upload from disk. Upload from URL.
No comments:
Post a Comment